What To Know About Jigsaws & Woodworking

Let's get some terms straight first so we are both clear about what we are talking about. It's a bit confusing but customary "jigsaw puzzles" were originally cut out on a "scroll saw" which used to be called a "jigsaw". Today, the term "jigsaw" refers to a hand-held transportable woodworking power tool while the term "scroll saw" refers to a stationary woodworking machine. Other way to look at it that in the case of a jigsaw, the tool is brought to the workpiece and in the case of the scroll saw the workpiece is brought to the machine. Other name for a jigsaw is "sabre saw."

I've been using jigsaws longer than I'd like to admit. I found the first one lying around my dad's woodworking shop in the basement of my childhood home. A few years after that, I purchased a cheap one from Sears. That jigsaw gave me the quick usefulness that all jigsaws contribute but there were persistent and annoying problems without apparent solutions: First, The blades had no guides so they would always gad away from the cut line, especially when I was trying to track curved pencil lines. Second, when cutting curves in thick material, the jigsaw blade would bend toward the surface of curves. Third, early jigsaws did not have orbital pendulum action and so they would load up and burn in thick materials. Changing blades required a screwdriver and you had to be faithful not to lose the set screw.

Jigsaw Name Puzzles

Today's top-quality jigsaws have eliminated all of those problems and are, by comparison to the earlier models, revolutionary. I will confine my remarks to better ability jigsaws because there are still agreement basement models out there with the problems I just outlined. Having said that, here are the important things that you should be seeing for in your next jigsaw:

At the top of my list are the subjects of blade tracking and blade guides. Take a close look at how each jigsaw constructor has approached these challenges because you are probably not going to get a chance to try out your next jigsaw before buying it. Look for specifics: Some manufacturers naturally say something like "superior blade tracking" without saying how this is accomplished. Others are convincingly descriptive.

Another issue with all jigsaws is wood splintering. Most, but not all, jigsaw blades are designed to cut on the upward stroke which means that the splintering often occurs on the good side of the board or plywood. Splintering can be minimized in two ways: (1) fine-cut blades and (2) anti-splinter inserts mounted in the saw foot immediately adjacent to each side of the blade. Fine-cut blades cut gradually and so if speed is a requirement and you are using a more aggressively-toothed jigsaw blade, a splinter insert is an absolute necessity unless you plan to sand and/or rout away the splintered area later.

Frequent blade changes are a fact of life with all jigsaws. In the interest of output efficiency, this process should be as fast and easy as possible. Gone are the days of screwdrivers, Allen wrenches and set screws. You want a jigsaw that lets you pop blades in and out in rapid fashion.

If you are health aware and want to minimize airborne dust in your work area, you may want to gain dust right at its source by connecting a vacuum hose to the jigsaw. In that case, check for a dust port and make sure that it is compatible with your vacuum hose. Personally, I prefer to wear a good dust mask and thus avoid the inconvenience of dragging a vacuum hose along with the jigsaw when I am trying to operate the engine along curves.

I mentioned orbital pendulum action above and I would not even consider buying a jigsaw without it. My first orbital engine was a Bosch barrel grip model. I was allowed to try one out in a woodworking store while I was on a company trip and it went home to Hawaii in my suitcase. Here's why: The salesman had a piece of eight-quarter White Oak and encouraged me to cut some curves in it. There were four orbital settings on that engine with the first being "no orbital action" and each one after that being more aggressive than the one before. With the orbit in the "off" position, I began a cut. As I expected, the engine gradually labored straight through the cut and I knew that if I pushed it any harder, the jigsaw blade would whether burn or break. Then, at the hint of the salesman, I put the orbit lever in position "4," the most aggressive, and made Other cut. The blade flew straight through the thick Oak as if it were butter. There is a bit more splintering than before but not well that much. Sold, American!

A side advantage of an oscillating jigsaw is extended blade life. When a blade is stuck inside a cut, it has nowhere to go to dissipate the heat. The pendulum action oscillates the blade in and out of the cutting face, letting cool air in while the blade is momentarily positioned away from the cut. At the same time, the accumulated sawdust is allowed to drop out of the cut so the blade is always cutting new wood, not old sawdust. That's why it can go faster and cooler.

Most good jigsaws, but not all, have Electronic Speed operate (Esc) which is an important nicety. Esc is like the cruise operate on your car: It maintains a constant speed with changing load conditions. The harder you push the jigsaw, the more electrical power is delivered automatically to the motor so that the saw blade will not slow down. The analogy is your car on cruise operate going up a hill.

Many jigsaws today are ready in two different body styles: barrel grip and top-handle (sometimes called D-handle). I have owned both and I have a personal preference for the barrel grip style because it is easier to operate when making fine cuts. Just like when using a router or any hand power tool, a low center of gravity and a solid grip equate to better control. With a top-handle jigsaw, your hand is at the top of a taller engine and the tendency to tip over is greater. With a barrel grip jigsaw, the center of gravity is as low as it can be. There is a knob on top, right over the jigsaw blade, for your other hand for better control. The big, round barrel is easier to hang onto than the thinner D-Handle.

Jigsaw manufacturers normally part motor power in terms of amperage, rather than horsepower. This is fine because amperage is a more trustworthy indicator of actual power than horsepower. The more amperage, the more power and power is important when cutting thick or dense materials.

The speed of the jigsaw blade is expressed in "strokes per minute" or "Spm." The more, the better.

Cutting depth is something you will want to consider when dealing with very thick or dense materials. In soft wood, cutting depth refers to the maximum length in the middle of the lowest tooth on the blade and the foot plate of the jigsaw when the blade is fully extended. In metal, plastic or other materials, cutting depth is based on the ability of the saw and blade to cut straight through dense or defiant materials.

Jigsaws are often used to cut expensive and delicate materials such as veneered plywood panels and a standard, steel foot plate may leave scratches as it travels along behind the blade. Some manufacturers offer coated foot plates, some contribute an "overshoe" for the foot plate and some fully fail to address this issue. If you cut delicate materials that can be well marred, pay faithful concentration to this feature (or lack of it.)

Machine weight is the next consideration. My knee-jerk reaction is to look for the lightest engine so that I won't tire so well while a long day of cutting. On second thought, the light weight is nowhere near the advantage as it would be in, say, an impact driver or electric drill because the jigsaw's weight is roughly always resting on the material being cut. Further, light weight could mean that the constructor skimped on building materials, possibly substituting plastic parts for metal as a cost savings.

Stroke length is the length the saw teeth travel up and down while cutting. This is roughly universally one-inch and so it is not a beneficial estimate when comparing models from different makers. Generally speaking, the longer the stroke, the faster the cut and the shorter the stroke, the smoother the cut.

Jigsaws can make bevel cuts, normally up to 45 degrees from vertical, both left and right. The more bevel, the thinner the material that can be cut. Adjusting the bevel can be hard or easy. Some jigsaws need you to use a screwdriver, hex wrench or Allen wrench to loosen or tighten a set screw that holds the foot in a singular position. Other jigsaws are designed with the adjusting mechanism built-in and, thus, requiring no tools. Opt for the latter when possible, all things else considered.

All jigsaws vibrate and make noise. Obviously the less vibration and noise the better. Vibration is transmitted to the point of cutting and affects your ability to operate the cut. More importantly, vibration is tiring when it goes into the operator's hand and arm. Varied jigsaw manufacturers have approached this question in different ways but the most base anti-vibration technique is to "counterbalance" the motor. The other way is to put vibration-absorbing material on the surface surfaces of the engine that come into direct caress with the hand(s) of the operator. Padding will not, of course, minimize the vibration transmitted to the jigsaw blade at the point of cutting. Noise discount varies by engine design and the only way to make this comparison requires running the jigsaws you are inspecting for purchase.

Some jigsaws come qualified with a variable speed wheel to set the maximum speed of the tool for better cutting results in different materials. This is different than the speed operate of the variable speed trigger. Full speed on the trigger will always be little by the setting of the variable speed wheel. Most jigsaw triggers have a lock-on feature because keeping the trigger on all day long can well make your hand go numb. Barrel grip jigsaws do not have a trigger but use a lock-on type thumb switch instead. If you have the variable speed set at half-speed and you lock the trigger or thumb switch, you will get half-speed at full trigger deflection until you turn the setting on the wheel.

Most jigsaws come qualified with some sort of air blower to keep chips away from the cut line. The air blower on the earlier machines was settled half-way in the middle of the operator's chin and nose. Some manufacturers mount the blower nozzle near the point of cutting, others on the top of the machine. Some have adjustable nozzles. The important thing is productive chip and dust discharge so you can see where you are supposed to cut.

Another aid to clear foresight of the cut line is a built-in light. Led lights are best because they are lively white and last virtually forever. Just in case they don't, see if they are replaceable and available.

There are several types of jigsaw blades ready and you will have to use the kind that your jigsaw is designed to accept. There is a disagreement in blade types. The T-shank is my preference because it stays locked in the saw plunger. Other types comprise tang shank and U-shank. Once you know what type of blades your jigsaw requires, be sure to check for the availability of blade designs accepted to the work you will be doing. Rough cut blades power straight through thick and base materials but leave a lot of splinters.

Fine-cut blades have many more teeth, leave fewer and smaller splinters but cut slower and are Generally shorter in length. They also may be thinner (front to back) to allow for tighter turns around sharp curves. They will break more well than a base blade. Metal cutting blades are also available. Use these only for metal because they will not cut wood very well and they will load up and burn in wood. On the other hand, a wood-cutting blade will not be able to cut metal effectively. Depending on the manufacturer, there are many other specialized types of jigsaw blades available. Make sure you always have abundance of extra blades on hand to avoid unexpected trips to the store right in the middle of a job.

What To Know About Jigsaws & Woodworking